New Arrival I-2015 Multi-Diag Access J2534 Pass-Thru OBD2 Device
Latest version: V2015.01
Support 23 brands updated, 5300 new systems (list of systems updated in Multi-Diag since DVD IV-2013).
Ideal for independent workshops require a diagnostic tool that truly multi-brand delivers in-depth information on a wide range of vehicles.
Supported Languages: Bulgarian, Croatian, Czech, Danish, Dutch, English, Finnish, French, German, Hebrew, Hungarian, Italian, Polish, Portuguese, Romanian, Russian, Serbian, Slovenian, Spanish, Swedish, Turkish.
New I-2015 Multi-Diag Access J2534 Pass-Thru OBD2 Device
Top 4 Reasons to Get I-2015 J2534:
1. Latest Version: V2015.01
2. Support Multi-languages: English/ Spanish/ German/ French/ Italian/ Portuguese/ Bulgarian/ Croatian/ Czech/ Danish/ Dutch/ Finnish/ Hebrew/ Hungarian/ Polish/ Romanian/ Russian/ Serbian/ Slovenian/ Swedish/ Turkish
3. Support 23 Brands Updated, 5300 New Systems
4. Operating System: Windows XP; Windows 7 32bit
Software Activation Notice:
1. Must disconnect network when install the software.
2. Must watch our installation video when install the software and drivers. (Please contact customer service to get the installation video)
3. I-2015V Multi-Diag Access J2534 needs activation, after installing the software pls send ID (format is only 31-xxxxxxxxxxx) to us, we will send the activation code.
Multi-Diag J2534 Functions:
After selecting the car manufacturer, then you can make the diagnosis for the different menus on offer (depending on cars models):
1. Maintenance
Diagnosis codes from all computers
Reset maintenance interval
Modification of the sewage
Read / erase fault calculators
Maintenance of the particulate filter
2. Air Conditioning
Diagnosis of cooling electronic
Reading settings cooling circuit,
Test servo actuators
3. Pollution Control
Diagnosis of the particulate filter
Electronic control of pollutant emissions
Control of the Lambda probe
4. Liaison to the Ground
Electronic configuration of the size of tires,
Electronic configuration of tires (winter / summer),
Setting valves tire pressure
Diagnosis and management of shock-driven
Calibration of the sensor angle Driving (initialization of the steering angle)
5. Body
Implementation of safety airbags (lock / unlock)
Reconfiguration of a new calculator Airbag,
Diagnosis of calculators Airbag,
Rain sensor windshield (reading and erasing fault)
Test panel and activators of lights,
Setting Xenon headlights,
Rear radar
6. Post-Equipment
Setting up the radio,
Configuration loader CD,
Setting alarms
Configuration of the coupler,
Configuration bicycle loading system
7. Braking
Diagnosis of calculators ABS, ESP.
Diagnosis and unlock electric brakes.
Flush the brake system.
8. Motor
Diagnosis of any calculator injection engine (diesel, gasoline, flexfuel, etc. ..)
Programming of injectors
Electronic configuration of the EGR valve
9. Expert Mode
Diagnosis of advanced computers,
Configuration of comfort functions,
Change the language of the instrument panel,
physical measures (option with a probe - not supplied)
Direct access to all functions of diagnosis.
V2015.1 Multi Diag Access J2534 System Requirements:
*O.S.: Windows XP; Windows 7 32bit
*CPU: Pentium/Athlon 1.8 GHz or higher
*RAM: 256 MB of system memory
*Hard Drive: 10 GB of available space
*VCI (vehicle communication Interface)
*DVD-ROM
*No Internet, WIFI
*No Antivirus software
Installation multi-diag 1-2015:
1. Before installation to ensure not having connection networks or wifi active
2. Open folder (1) Key on the CD and run the file KeyUpdate. Then confirm and wait for the message successfully installed XXXXXX and OK
3. Start the installation folder (2) 1-2015
If during your installation software request an unlock key 31-xxxxxxxxxx contact us with the key not give you the activation key valid
Select the language it will continue the installation to completion after the message asking do you restart known not to install the following update etc once the last install
Once the message you want to ask not restart known
4. Go to the following folder C: \ ACTIA \ portal and then delete the file WEGT.EXE
5. Once delete this file, open folder (1) Key on the CD and run the file KeyUpdate. Then confirm and wait for the message successfully installed XXXXXX and OK
6. Then install: xs-ime-pt-207p-workshop.exe. You can then restart the pc
Software Display:
Multi-Diag J2534 Packing List:
VCI (Vehicle Communication Interface)
DB25 to OBD-2 Male cable
OBD2 Male to OBD2 Female cable
